Joint is a separation provided in a building that allows it’s component parts to move with respect to each other; a joint where two placements of concrete meet. The purpose of a construction joint is to allow for some horizontal movement, while being rigid against rotational and vertical movement.
The need for joints in concrete;
The absence or improper use of a construction joint will lead to slab failure with continual defects and joint deterioration due to the relative horizontal, vertical and rotational strains and pressures. Continual vehicular traffic transferring over a badly placed construction joint will cause fracturing and spalling. Rectifying these problems afterwards can be very costly and in some cases the entire concrete slab may need to be destroyed and replaced. Using the patented Ideal Joint systems will offer long term benefits and cost savings for every slab-on-grade project.
Joints will be designated by a terminology based on the following characteristics: resistance, configuration, formation, location, and type of structure.
- Resistance: Tied or reinforced, doweled, non doweled, plain
- Configuration: Butt, lap, tongue, and groove.
- Formation: Sawed, hand-formed, tooled, grooved, insert formed.
- Location: Transverse, longitudinal, vertical, horizontal
- Type of Structure: Bridge, pavement, slab-on-grade building etc.
The prerequisite for joints in concrete
Given below are a few of the prerequisites that are needed to be maintained when applying joints.
- The surface of all construction joints must be cleaned and all laitance must be removed.
- Before new concrete can be placed all construction joints have to be wetted and all standing water removed.
- The strength of a structure must not be impaired by construction joints.
- All construction joints located within the middle third of spans of slabs, beams, and girders must be clean and dry.
- Vertical support members that are still plastic must not be used to support beams, girders, or slabs.
- Except when shown otherwise in design drawings or specifications, beams, girders, haunches, drop panels, and capitals are to be placed monolithically as part of a slab system.
Different types of joints in concrete
Concrete expands & shrinks with variations in moisture and temp. Joints in concrete slabs can be created by forming, sawing, tooling, & placement of joint formers. Different types of concrete joints are discussed below.
Construction joints
A construction joint is a joint between slabs that results when concrete is placed at different times. This type of joint can be further broken down into transverse and longitudinal construction joints. Longitudinal construction joints also allow slab warping without appreciable separation or cracking of the slabs. Construction joints are provided at surfaces where two successive placements of concrete occur. They are typically placed at the end of a day’s work or when concrete placement is stopped for a longer time than the initial setting time of concrete. For slabs they may be designed to allow movement and/or to transfer load. The locations of construction joints should be predetermined.
There are two types of construction joints.
Butt Joints: The simplest type of construction joint is a butt type formed by the usual bulkhead board. This joint is suitable for thin slabs.
Tongue and Groove Joints: Slabs can use a type of joint that resembles tongue and groove lumber construction. The keyway may be formed by fastening metal, wood, or pre-molded key material to a wood bulkhead. The concrete above the joint should be hand-tooled or saved to match a control joint in appearance.
Expansion joints
Expansion joints are used to allow for expansion and contraction of concrete during the curing period and service. These Joints are used to permit dimensional changes in concrete due to load. This joint helps to separate or isolate, areas or members that could be affected by any such dimensional changes.
Contraction joints
Contraction joints are intended to create weakened planes in the concrete and regulate the location where cracks, as a result of dimensional changes, can occur. Contraction/control joints are placed in concrete slabs to control random cracking. A fresh concrete mixture is a fluid, plastic mass that can be molded into virtually any shape, but as the material hardens there is a reduction in volume or shrinkage. When shrinkage is restrained by contact with supporting soils, granular fill, adjoining structures, or reinforcement within the concrete, tensile stresses develop within the concrete section. Contraction joints consist of a region with a reduced concrete cross section and reduced reinforcement. The concrete cross section should be reduced by a minimum of 25 percent to ensure that the section is weak enough for a crack to form.
Isolation joints
Isolation or expansion joints are provided to separate or isolate slabs from other parts of the building, such as walls & footings or columns; also driveways and patios from sidewalks, garage slabs, light poles or other points of restraint. Joints permit free vertical and horizontal movement between adjacent parts of the structure and help reduce cracking when these movements are restrained. An isolation joint is used to lessen compressive stresses that develop at T- and unsymmetrical intersections, ramps, bridges, building foundations, drainage inlets, manholes, and anywhere differential movement between the pavement and a structure (or another existing pavement) may take place. They are typically filled with a joint filler material to prevent water and dirt infiltration.
Seismic Joints
Seismic joints are wide expansion joints provide to separate portions of buildings dissimilar in mass and stiffness. The seismic joint coverage must allow movement, and be architecturally acceptable. The width of a seismic joint should be equal to the sum of the total deflections at the level involved from the base of the two buildings, but not less than the arbitrary rule of 1 in. for the first 20 ft of height above the ground, plus 1/2 in. for each 10 ft additional height. The determination of these deflections will be the summation of the story drift in addition to the building’s flexural deflection to the level involved. Shear wall buildings, being much stiffer, need a seismic joint only, say, half as wide, since the earthquake oscillations of shear wall buildings will be much smaller than those of framed buildings.
Conclusion
The detailing of joints is an important aspect of building design and this is provided by experienced experts only. Well designed and constructed joints will enhance both a building’s appearance and give the desired performance.
